warning light RENAULT KANGOO 2013 X61 / 2.G Petrol V42 Injection Workshop Manual

17B-11V2 MR-376-X76-17B050$050.mif
PETROL INJECTION
Fault finding – Features17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
Engine temperature management
The engine is cooled by a 2-speed fan assembly.
To cool the engine, the first speed of the fan assembly is activated if the coolant temperature exceeds 99°C or 94°C
(F4R400/402/403 engines), then the second speed is activated if the temperature exceeds the 102°C or 97°C
(F4R400/402/403 engines). A "very high temperature" warning light illuminates on the instrument panel if the
temperature exceeds 118°C or 113°C (F4R400/402/403 engines).

17B-21
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$081.mif
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF001
PRESENT OR
STOREDCOOLANT TEMPERATURE SENSOR CIRCUIT4.DEF: Voltage too low
5.DEF: Voltage too high
6.DEF: Micro-cut
NOTESSpecial notes:
– The OBD and Level 1 warning lights illuminate.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the connection and condition of the connector of the coolant temperature sensor, component code 244
and of the connections of the injection computer, component code 120.
If the connector(s) are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Disconnect the connector of the injection computer, component code 120 (see MR 388 (Logan and Sandero), MR
451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 17B,
Petrol injection, Petrol injection computer: Removal - Refitting).
Measure the resistance of component 244 by connections 3JK and 3C of the injection computer connector,
component code 120.
If the resistance of the coolant temperature sensor, component code 244 is not between 100   X  10 k (K7M,
K4M, D4D engines), 85   X  82 k (Duster F4R and K4M engine) at ambient temperature: replace the coolant
temperature sensor, component code 244 (see MR 388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia
2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 19A, Cooling, Coolant temperature
sensor: Removal - Refitting).
Check the insulation, continuity and absence of interference resistance on the following connections:
–3JK between components 120 and 244.
–3C between components 120 and 244.
If the connection or connections are faulty and if there is a repair method (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the fault is still present, contact the Techline.
V42_V04_DF001/ V42_V05_DF001/V42_V06_DF001/V42_V14_DF001/V42_V16_DF001/V42_V18_DF001
PETROL INJECTION
Fault finding – Interpretation of faults

17B-22
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF002
PRESENT OR
STOREDAIR TEMPERATURE SENSOR CIRCUIT2.DEF: Signal outside lower limit.
3.DEF: Signal outside upper limit.
NOTESSpecial notes:
– The OBD and Level 1 warning lights illuminate.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the connection and condition of the connector of the air temperature sensor, component code 272 and of
the connections of the injection computer, component code 120.
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of the air temperature sensor, component code 272 between connections 3B and 3JQ.
If the resistance measured is not between 300   X  6 k or 100   X  50 k  (Duster F4R engine) or 50 
 X  50 k (Duster K4M engine) at ambient temperature: replace the air temperature sensor, component code
272.
Check the insulation, continuity and absence of interference resistance on the following connections:
–3B between components 272 and 120.
–3JQ between components 272 and 120.
If the connection or connections are faulty and if there is a repair method (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair
), repair the wiring, otherwise replace the wiring.
If the fault is still present, contact the Techline.
V42_V04_DF002/ V42_V05_DF002/V42_V06_DF002/V42_V14_DF002/V42_V16_DF002/V42_V18_DF002

17B-23
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF011
PRESENT OR
STOREDSENSOR FEED VOLTAGE NO. 11.DEF: Above maximum threshold.
2.DEF: Below minimum threshold.
NOTESSpecial notes:
– The OBD and Level 2 warning lights illuminate.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Disconnect the accelerator pedal sensor gang 1, component code 921 then switch on the ignition. Wait several
seconds so that the computer can update the fault status.
If the fault changes from present to stored: Replace the accelerator pedal sensor gang 1, component code 921
(see MR 388 (Logan and Sandero), MR 451 (Duster) MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR
374 (Kangoo VLL), Mechanical, 37A, Mechanical component controls, Accelerator pedal: Removal -
Refitting).
Disconnect the motorised throttle valve, component code 1076 then switch on the ignition (see MR 388 (Logan
and Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL),
Mechanical, 12A, Fuel mixture, Throttle valve: Removal - Refitting).
Wait several seconds so that the computer can update the fault status.
If the fault changes from present to stored: Replace the damper valve position sensor, component code 1076, (see
MR 388 (Logan and Sandero), MR 451 (Duster) or MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR
374 (Kangoo VLL), Mechanical, 12A, Fuel mixture, Throttle valve: Removal - Refitting) referring to the
Replacement of components section.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3LR between components 921 and 120,
–3LT between components 921 and 120,
–3MN between components 1076 and 120,
–3MO between components 1076 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
V42_V04_DF011/ V42_V05_DF011/V42_V06_DF011/V42_V14_DF011/V42_V16_DF011/V42_V18_DF011

17B-24
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF012
PRESENT OR
STOREDSENSOR SUPPLY VOLTAGE NO. 21.DEF: Above maximum threshold.
2.DEF: Below minimum threshold.
NOTESSpecial notes:
– The OBD and Level 2 warning lights illuminate.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Disconnect the accelerator pedal sensor gang 2, component code 921 then switch on the ignition (see MR 388
(Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo
VLL), Mechanical, 37A, Mechanical component controls, Accelerator pedal: Removal - Refitting).
Wait several seconds so that the computer can update the fault status.
If the fault changes from present to stored: Replace the accelerator pedal sensor gang 2, component code 921
(see MR 388 (Logan and Sandero), MR 451 (Duster) or MR 423 (Thalia 2/Symbol 2), Mechanical, 37A,
Mechanical component controls, Accelerator pedal: Removal - Refitting).
Disconnect the manifold pressure sensor, component code 147, then switch on the ignition.
Wait several seconds so that the computer can update the fault status.
If the fault changes from present to stored: Replace the inlet pressure sensor, component code 147.
Disconnect the Freon pressure sensor, component code 1202, then switch on the ignition (see MR 388 (Logan
and Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL),
Mechanical, 62A, Air conditioning, Pressure sensor: Removal - Refitting).
Wait several seconds so that the computer can update the fault status.
If the fault changes from present to stored: Replace the Freon pressure sensor, component code 1202 (see MR
388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374
(Kangoo VLL), Mechanical, 62A, Air conditioning, Pressure sensor: Removal - Refitting).
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3LU between components 921 and 120,
–3LV between components 921 and 120,
–3AJP between components 147 and 120,
–3AJR between components 147 and 120,
–38Y between components 1202 and 120,
–38U between components 1202 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
V42_V04_DF012/ V42_V05_DF012/V42_V06_DF012/V42_V14_DF012/V42_V16_DF012/V42_V18_DF012

17B-28
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF026
PRESENT OR
STOREDCYLINDER 1 INJECTOR CONTROL CIRCUITCO: Open circuit.
CC.1: Short-circuit on +12 volts.
CC.0: Short circuit to earth
NOTESThe fault changes from stored to present when the engine is running at idle
speed.
Special notes:
For CC.1 and CO, the OBD and Level 1 warning lights illuminate.
For CC.0, the Level 2 warning light illuminates.
Measure the resistance of the injector between 0°C and 40°C.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the connection and condition of the connector of the injection computer, component code 120 and of the
cylinder 1 injector, component code 193.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of the cylinder 1 injector, component code 193 between connections 3FB and 3CR.
If the resistance measured is not between 11   X  20  (K4M, D4D engines), 11.5   X  12.5  (F4R engine),
9.2   X  17  (K7M engine) or 14   X  15  (K4M engine on Duster): replace the cylinder 1 injector,
component code 193 (see MR 388 (Logan and Sandero), Mechanical, 13A, Fuel supply, Injector rail -
Injectors: Removal - Refitting, MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374
(Kangoo VLL), Mechanical, 17B, Petrol injection, Injector rail - Injectors: Removal - Refitting).
V42_V04_DF026/ V42_V05_DF026/V42_V06_DF026/V42_V14_DF026/V42_V16_DF026/V42_V18_DF026

17B-30
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF027
PRESENT OR
STOREDINJECTOR CYLINDER 2 CONTROL CIRCUITCO: Open circuit.
CC.1: Short-circuit on +12 volts.
CC.0: Short circuit to earth
NOTESThe fault changes from stored to present when the engine is running at idle
speed.
Special notes:
For CC.1 and CO, the OBD and Level 1 warning lights illuminate.
For CC.0, the Level 2 warning light illuminates.
Measure the resistance of the injector between 0°C and 40°C.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the connection and condition of the connector of the injection computer, component code 120 and of the
cylinder 2 injector, component code 194.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of the cylinder 2 injector, component code 194 between connections 3FB and 3CS.
If the resistance measured is not between 11   X  20  (K4M, D4D engines), 11.5   X  12.5  (F4R engine),
9.2   X  17  (K7M engine) or 14   X  15  (K4M engine on Duster): replace the cylinder 2 injector,
component code 194 (see MR 388, (Logan and Sandero), Mechanical, 13A, Fuel supply, Injector rail -
Injectors: Removal - Refitting, MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374
(Kangoo VLL), Mechanical, 17B, Petrol injection, Injector rail - Injectors: Removal - Refitting
).
Run command AC006 Cylinder 2 injector and check the operation of the injector with a listening test.
V42_V04_DF027/ V42_V05_DF027/V42_V06_DF027/V42_V14_DF027/V42_V16_DF027/V42_V18_DF027

17B-32
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF028
PRESENT OR
STOREDCYLINDER 3 INJECTOR CONTROL CIRCUITCO: Open circuit.
CC.1: Short-circuit on +12 volts.
CC.0: Short circuit to earth
NOTESThe fault changes from stored to present when the engine is running at idle
speed.
Special notes:
For CC.1 and CO, the OBD and Level 1 warning lights illuminate.
For CC.0, the Level 2 warning light illuminates.
Measure the resistance of the injector between 0°C and 40°C.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the connection and condition of the connector of the injection computer, component code 120 and of the
cylinder 3 injector, component code 195.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of the cylinder 3 injector, component code 195 between connections 3FB and 3CT.
If the resistance measured is not between 11   X  20  (K4M, D4D engines), 11.5   X  12.5  (F4R engine),
9.2   X  17  (K7M engine) or 14   X  15  (K4M engine on Duster): replace the cylinder 3 injector,
component code 195 (see MR 388, (Logan and Sandero), Mechanical, 13A, Fuel supply, Injector rail -
Injectors: Removal - Refitting, MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6), MR 374
(Kangoo VLL), Mechanical, 17B, Petrol injection, Injector rail - Injectors: Removal - Refitting).
Run command
AC007 Cylinder 3 injector and check the operation of the injector with a listening test.
V42_V04_DF028/ V42_V05_DF028/V42_V06_DF028/V42_V14_DF028/V42_V16_DF028/V42_V18_DF028

17B-34
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF029
PRESENT OR
STOREDCYLINDER 4 INJECTOR CONTROL CIRCUITCO: Open circuit.
CC.1: Short-circuit on +12 volts.
CC.0: Short circuit to earth
NOTESThe fault changes from stored to present when the engine is running at idle
speed.
Special notes:
For CC.1 and CO, the OBD and Level 1 warning lights illuminate.
For CC.0, the Level 2 warning light illuminates.
Measure the resistance of the injector between 0°C and 40°C.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the connection and condition of the connector of the injection computer, component code 120 and of the
cylinder 4 injector, component code 196.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of the cylinder 4 injector, component code196 between connections3FB and 3CU.
If the resistance measured is not between 11   X  20  (K4M, D4D engines), 11.5   X  12.5  (F4R engine),
9.2   X  17  (K7M engine) or 14   X  15  (K4M engine on Duster): replace the cylinder 4 injector,
component code 196 (see MR 388 (Logan and Sandero), Mechanical, 13A, Fuel supply, Injector rail -
Injectors: Removal - Refitting, MR 451 (Duster) or MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6), MR 374
(Kangoo VLL), Mechanical, 17B, Petrol injection, Injector rail - Injectors: Removal - Refitting
).
Run command AC008 Cylinder 4 injector and check the operation of the injector with a listening test.
V42_V04_DF029/ V42_V05_DF029/V42_V06_DF029/V42_V14_DF029/V42_V16_DF029/V42_V18_DF029

17B-36
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF038
PRESENT OR
STOREDCOMPUTER1.DEF: Internal electronic fault.
NOTESSpecial notes:
The OBD and Level 2 warning lights illuminate.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Contact the Techline.
V42_V04_DF038/ V42_V05_DF038/V42_V06_DF038/V42_V14_DF038/V42_V16_DF038/V42_V18_DF038